Application Intelligence Session

To create an Application Intelligence Session:

1.

On the left navigation pane, select Traffic > Solutions > Application Intelligence.

2.

Click Create New. The Create Application Intelligence Session page appears.

Note:   If the Create button is disabled, check whether a valid license for Application Metadata Intelligence or Application Filtering Intelligence is available.

3.

In the Basic Info section complete the following:

■

Enter the name and description (optional).

■

Select Physical in the Environment field.

■

Select the node from the list of nodes.

4.

In the Configurations section, view the following:

a.

The export interval is fixed at five minutes, at which the Application Intelligence session will generate the reports for application monitoring.

Note:  When you upgrade to 6.4, the prior configured export interval will be updated to five minutes.

b.

Select a GigaSMART Group. You can also choose to create a new GigaSMART Group.

•

Provide a name in the Alias field.

•

Select a port or multiple ports from the Port List.

•

Click Save.

For more information about creating a new GigaSMART group, refer to the Configure a GigaSMART Group section.

c.

Select the required interface. By default, Management Interface is enabled. To export the data through IP interface, uncheck the Management Interface check box. You can view the IP Interface field only after you select a GigaSMART Group.

d.

Select an IP interface that is used to create a dedicated channel to communicate all application statistics to GigaVUE-FM. You can also choose to create a new IP interface. For more information, refer to the IP Interfaces section.

e.

Enable the fastmode option for performance (less CPU cycles and less memory utilization) improvement. When the fastmode is enabled, some or all of the attributes of the applications will be disabled. You can view the list of attributes/applications available in the fast mode by navigating to the app editor under AMI feature in the FM. If all the attributes of the application are disabled then the application itself is disabled. Refer Fast Mode for more information.

Note:  The fastmode feature is supported only on GigaVUE HC Series. The fastmode option can be enabled or disabled only when creating a new application intelligence session.

5.

In the User Defined Applications section, select the template from the inventory where it was created.

6.

If you are unable to view the required port in the Port field, perform these steps:

o

Click Port Editor. Select the Type as Tool from the drop-down list for the required Port Id. Select OK.

The selected Port appears in the list.

o

Select the Type as:

o

IPv4 - to allow the traffic in IPv4 interface.

o

IPv6 - to allow the traffic in IPv6 interface.

o

Provide the IP Address, IP Mask, Gateway, and MTU. Provide the IP address corresponding to the IP interface selected.

o

Click Save.

7.

In the DestinationSettings, enter the destination IP address. The version of IP address in the Destination field should be same as the version of IP address defined in the IP-interface (applicable only when IP interface is selected). By default, the IP address of the GigaVUE-FM interface is displayed.

8.

In the Source Traffic section, select a source port that require application monitoring in the Source ports field. Source port can be a single port, multiple ports, and port groups.

Note:   Ports already used as source ports in the intent-based orchestrated solution will not be listed in the drop-down.

9.

Configure the rules for filtering the required traffic in the L2-L4 Rules fields. To configure a rule:

a.

Click Select Conditions. Select the required parameters from the drop-down list.

b.

Select the value for the parameters from the drop-down.

c.

Select the required options:

•

Pass or Drop - Based on the parameter selected in the Conditions fields, the traffic that matches the conditions will either be passed or dropped.

•

Bidirectional - Allows the traffic in both directions of the flow.

Note:  Click “+” to create multiple rules for filtering the required traffic, and click “+ New Source Traffic” to create multiple sources with filtering options.

10.

Click Save. The session created is added in the list view.

You can upgrade the protocol signature by upgrading the image file on the GigaSMART card, and by uploading the GigaSMART card image to GigaVUE-FM from the Internal Server or External Server. To select the image, follow the steps:

• Internal Server—Upload the GigaSMART card image to GigaVUE-FM from the internal server and select the image that you need to upgrade from the selected GigaSMART card.
• External Server—Provide the location of the image in the external server that you need to upgrade from the GigaSMART card.

For more information on upgrading the image, refer to the following topics in the GigaVUE-OS Upgrade guide:

• Upgrade from an External Image Server
• Upgrade with GigaVUE‑FM as the Image Server

Disable Application Visibility in Application Intelligence Session

To disable Application Visibility, do the following:

1.

Edit the Application Intelligence Session.

2.

Disable the checkbox next to Monitoring Enabled.

3.

Select Save.

After disabling the monitoring session, the Application Intelligence dashboard does not receive the updates and a message " Monitoring has been disabled. Please enable monitoring to get latest data " is shown in red at the top of the dashboard.