GigaSMART ERSPAN Tunnel Decapsulation

ERSPAN Type III is similar to ERSPAN Type II but has a hardware timestamp in the packet. The hardware timestamp needs to be translated into a usable timestamp.

The UTC timestamp can be calculated, based on the reference hardware timestamp and the reference UTC timestamp carried in marker packets that are periodically sent over UDP. The calculated UTC timestamp can then be appended to the packets as a trailer.

Marker packets have a fixed length and are identified by a signature of 0xA5A5A5A5. If the marker packet session ID matches the ERSPAN session ID, the UTC timestamp can be extracted from the marker packet. An ERSPAN session is defined by a map that uses an ERSPAN GigaSMART operation (gsop).

There are three timestamp formats: None, GigaSMART, and X12-TS (for PRT-H00-X12TS). The timestamp options are set from the GigaSMART Group page, which is accessed by selecting GigaSMART > GigaSMART Groups > GigaSMART Groups, and then clicking New or editing an existing GigaSMART Group. 1 shows the timestamp format options. If the timestamp format is Disabled, ERSPAN Type III packets are parsed and the ERSPAN header is removed by GigaSMART. The inner packets are forwarded to a tool port. If the timestamp format is GigaSMART or X12-TS, a trailer containing the recovered timestamp is added to the inner packets before they are forwarded to a tool port.

The GigaSMART timestamp is added to the GigaSMART trailer. For the format of the GigaSMART trailer, refer to GigaSMART Trailer Reference. The x12-ts timestamp is added to the PRT-H00-X12TS trailer. For the format of the PRT-H00X12TS trailer, refer to the GigaVUE-OS CLI Reference Guide.

Only 10 ERSPAN sessions are supported per GigaSMART Group (gsgroup) when the timestamp format is configured to GigaSMART or X12-TS.

In summary for ERSPAN Type III encapsulation, GigaSMART does the following:

ERSPAN granularity is a setting that can be configured on the Cisco switch for the level of detail of the hardware timestamp in marker packets.

A marker packet will be considered overdue if it does not arrive by the following times:

ERSPAN statistics include a count of overdue packets. Refer to Display ERSPAN Statistics for how to display the output and to ERSPAN Statistics Definitions for descriptions of these statistics.

For the PRT-H00-X12TS format, you can obtain a unique ID identifying the port on which packets arrive. Use the following CLI command to display the mapping of ports to unique IDs:

(config) # show apps netflow port-id

===========================

Port       Netflow port-id

---------------------------

1/1/x1     1

1/1/x2     2

1/1/x3     3

1/1/x4     4

1/1/x5     5

1/1/x6     6

1/1/x7     7

1/1/x8     8

1/1/x9     9

1/1/x10    10

1/1/x11    11

1/1/x12    12

---------------------------

Use the GigaSMART Operation (GSOP) page to configure the ERSPAN decapsulation types and options. For example, you can specify an ERSPAN flow ID, from 0 to 1023. Use this option when decapsulating traffic received over a Cisco-standard ERSPAN tunnel. Both ERSPAN Type II and Type III header decapsulation are supported.

To access GigaSMART within GigaVUE‑FM, access a device that has been added to GigaVUE‑FM from the GigaVUE‑FM interface. GigaSMART appears in the navigation pane of the device view on supported devices. Refer to Access GigaSMART from GigaVUE‑FM for details.

ERSPAN Tunnel Header Removal

To configure a tunnel to capture the ERSPAN packets, remove the ERSPAN header, and then forward the packets to a tool port, set the ERSPAN Decapsulation Flow ID to zero when creating the GigaSMART operation as shown in 2.

Note:  A flow ID of zero is a wildcard value that matches all flow IDs.

2

Decapsulation Flow ID Set to Zero.

In the following example, a tunnel is configured to capture ERSPAN packets, then the ERSPAN header is removed and the packets are forwarded to a tool port.

Task	Description	UI Steps
1.	Configure a tool type of port.	a. Select Ports > All Ports. b. Click Quick Port Editor. c. Use Quick search to find the ports to configure. For example,1/1/g1. d. Set the type to Tool and select Enable. e. Click OK.
2.	Configure a GigaSMART group and associate it with a GigaSMART engine port.	a. From the device view, select GigaSMART > GigaSMART Groups > GigaSMART Groups. b. Click New. c. Type an alias in the Alias field (for example, gsgrp1) and enter an engine port in the Port List field (for example 1/3/e1). d. Click Save.
3.	Configure the IP interface.	a. Select Ports > IP Interfaces. b. Click New. c. On the IP Interfaces page, in the Alias and Description fields, enter the name and description for the IP interface. d. Click the Ports field and select the port from the drop-down list. e. Enter the IP address, subnet mask, gateway, and MTU settings in the respective fields. For example, port 1/1/g2, IP address 10.10.10.10, mask 255.255.225.0, gateway 0.10.10.1, and MTU 1500. f. Click on the GigaSMART Group field to select the GigaSMART group. g. Click Save.
4.	Configure the GigaSMART operation and assign it to the GigaSMART group. Note:  A flow ID of zero is a wildcard value that matches all flow IDs.	a. From the device view, select GigaSMART > GigaSMART Operations > GigaSMART Operation. b. Click New. c. Type an alias in the Alias field. d. From the GigaSMART Groups drop-down list, select the GigaSMART Group that you created in the second task. e. From the GigaSMART Operations (GSOP) drop-down list, select Tunnel Decapsulation. f. Select ERSPAN for the decapsulation type. g. Enter a value of 0 in the Flow ID field. The configuration should look like the example shown in 2 Decapsulation Flow ID Set to Zero.. h. Click Save.
5.	Create a map.	a. Select Maps > Maps > Maps. b. Click New. c. Type an alias in the Map Alias field that will help you identify this map. d. Select Regular and By Rule for the map type and subtype. e. Specify the network and tool ports in the Source and Destination fields, respectively. f. From the GSOP drop-down list, select the GigaSMART operation configured in task 4. g. Click Add a rule under Map Rules and create the following rule: Select IPv4 Protocol from the drop-down list and select GRE for Value, and then select Pass. h. Click Save.

ERSPAN Type III Tunnel Header Removal

In this example, a tunnel is configured to capture ERSPAN packets. ERSPAN Type III packets are parsed, the ERSPAN header is removed, and the timestamp is calculated. A timestamp trailer is added before the packets are forwarded to a tool port.

Note:  A flow ID of zero is a wildcard value that matches all flow IDs.

Task	Description	UI Steps
1.	Configure a port of type tool.	a. Select Ports > Ports > All Ports. b. Click Quick Port Editor. c. In the Quick View Editor, find the port to configure. d. Set Type to Tool. e. Select Enable f. Click OK. g. Close the Quick Port Editor.
2.	Configure a GigaSMART group and associate it with a GigaSMART engine port.	a. From the device view, select GigaSMART > GigaSMART Groups > GigaSMART Groups. b. Click New. c. Enter a name in the Alias field d. Select the engine port in the Port List field. e. Click Save.
3.	Configure the IP interface.	a. Select Ports > IP Interfaces. b. Click New. c. On the IP Interfaces page, in the Alias and Description fields, enter the name and description of the IP interface. d. Click the Ports field and select the tool port from the drop-down list. e. Enter the IP address, subnet mask, gateway, and MTU settings in the respective fields. For example, port 1/1/g2, IP address 10.10.10.10, mask 255.255.225.0, gateway 0.10.10.1, and MTU 1500. f. Click on the GigaSMART Group field to select the GigaSMART group. g. Click Save.
4.	Configure the GigaSMART operation and assign it to the GigaSMART group. Note:  A flow ID of zero is a wildcard value that matches all flow IDs.	a. From the device view, select GigaSMART > GigaSMART Operations (GSOP) > GigaSMART Operation. b. Click New. c. Type an alias in the Alias field. d. From the GigaSMART Groups drop-down list, select the GigaSMART Group that you created in the second task. e. From the GigaSMART Operations (GSOP) drop-down list, select Tunnel Decapsulation. f. Select ERSPAN for the decapsulation type. g. Enter a value of 0 in the Flow ID field. The configuration should look like the example shown in 2 Decapsulation Flow ID Set to Zero.. h. Click Save.
5.	Configure a timestamp trailer format.	a. From the device view, select GigaSMART > GigaSMART Group. b. Select the GigaSMART Group created in Task 2. c. Under GigaSMART Parameters, go to Tunnel Decapsulation. d. For ERSPAN Type III Timestamp Format, select GigaSMART e. Click Save.
6.	Create a map. The map contains a rule to allow marker packets (UDP) to be processed.	a. Select Maps > Maps > Maps. b. Click New. c. Type an alias in the Map Alias field that will help you identify this map. d. Select Regular and By Rule for the map type and subtype. e. Specify a network ports in the Source fields. f. Select the tool port configured in Task 1 in the Destination field g. From the GSOP drop-down list, select the GigaSMART operation configured in task 4. h. Click Add a Rule and create the first rule. Select Pass, then select IPv4 Protocol, and then select GRE fro Value. i. Click Add a Rule and create the second rule. Select Pass, then select IPv4 Protocol, and then select UDP for Value. j. Click Save.

To display ERSPAN statistics, select GigaSMART > GigaSMART Operations (GSOP) > Statistics. The ERSPAN statistics will be in the row labeled Tunnel Decap in the GS Operations column.

Refer to ERSPAN Statistics Definitions for descriptions of these statistics as well as to GigaSMART Operations Statistics Definitions.