interface

Configures settings for the eth0 Mgmt port, as well as the loopback (lo) interface, and eth1 and eth2 interface.

Adds a peer interface to a specified bonded interface. For example:

(config) # interface eth0 bond bond0

Provides a comment field for the interface, displayed whenever the interface records are listed in the CLI.

Enables or disables DHCP on the Mgmt interface. You can also use renew to renew the address currently leased by the Mgmt interface.

When DHCP is enabled, the Mgmt port gets its IP address and subnet mask from a DHCP server—a static address/netmask defined with the ip address argument is not used when DHCP is enabled. For example, the following command enables DHCP on the Mgmt port (eth0):

(config) # interface eth0 dhcp

Note:  By default, DHCP is enabled. This means that when you run the jump-start for the first time, the default reads, "[yes]." When it is run subsequently, it will indicate yes or no based on how it was set.

Sets the duplex mode for the Mgmt port. You can set it to full or auto (the default). If you set it to auto, also set speed to auto.

Note:   Starting in software version 5.5, half-duplex support has been deprecated from the management interfaces (eth0, eth1...). If half duplex was configured in a previous software version, it will remain intact following the upgrade to 5.5 or higher release. Update to full duplex, if required.

Specifies a static IPv4 address and netmask for the Mgmt port. Note that defining the IP address/netmask does NOT switch the Mgmt port over from DHCP if it is currently using it. You need to explicitly disable DHCP as well with no interface eth0 dhcp before the static address specified here is used.

You can specify the netmask using either the bit-count model or a dotted-quad (for example, /24 or 255.255.255.0). For example, the following command configures a static address of 192.168.1.0 with a netmask of /24:

(config) # interface eth0 ip address 192.168.1.0 /24

Configures IPv6 properties for the Mgmt port. You can specify a static address or accept an autoconfigured address. Setting the address does not enable its use—you also have to explicitly enable the IPv6 address with interface eth0 ipv6 enable.

Specifies the MTU for the Mgmt port. Specify a value in bytes (1518 is the largest size for a standard Ethernet packet). The range is 1280–9400. The default is 1500. It is recommended that you set the MTU value to 9400 on all platforms to avoid fragmentation.

Change the MTU value for the Mgmt port only after disabling IPv6 on that particular interface using the following command:

(config) # no interface <interface> ipv6 enable

Administratively shuts down the Mgmt port. If you do this, you will only be able to access the node over the serial console port.

Sets the speed for the Mgmt port. You can set it to 10Mb, 100Mb, 1000Mb, or auto. Setting the speed to auto also sets duplex to auto. If you set speed to one of the manual settings, the system will read the last autoconfigured setting for duplex and set it to the manual version of the autoconfigured value.

show interfaces

show interfaces eth0 brief

show interfaces eth0 configured

(config) # no interface eth0 bond bond0

(config) # no interface eth0 comment

(config) # no interface eth0 dhcp

(config) # no interface eth0 duplex

(config) # no interface eth0 ip address

(config) # no interface eth0 ipv6 address

(config) # no interface eth0 ipv6 address autoconfig

(config) # no interface eth0 ipv6 address autoconfig default

(config) # no interface eth0 ipv6 address autoconfig privacy

(config) # no interface eth2 ipv6 dhcp client enable

(config) # no interface eth0 ipv6 enable

(config) # no interface eth0 mtu

(config) # no interface eth0 shutdown

(config) # no interface eth0 speed