The Basic Commands
The following table lists each of the top level commands for the GigaVUE-OS CLI in Configure mode. Most commands have multiple supported arguments. You can see the exact arguments available at any point of command entry by typing it into the CLI followed by ?.
|
Command |
Description |
|
aaa |
Configure authentication, authorization, and accounting settings. |
|
banner |
Set a system login banner. |
|
bond |
Configure bonded interface settings. |
|
boot |
Configure system boot parameters. |
|
card |
Configure a card. On TA Series nodes, use the card command to enable additional ports on GigaVUE TA Series nodes. |
|
chassis |
Configure the chassis. |
|
clear |
Reset statistics or clear caches. |
|
cli |
Configure CLI shell options. |
|
clock |
Set the system clock or timezone. |
|
cluster |
Configure a cluster of connected nodes. |
|
configuration |
Manage configuration files. |
|
configure |
Enter Configure mode. |
|
coreboot |
Upgrades the BIOS image on GigaVUE-TA100, GigaVUE-TA100-CXP, GigaVUE‑HC1, GigaVUE‑HC3 |
|
crypto |
Manage X.509 certificates for the node’s Web server. |
|
debug |
Generate a dump file for use in debugging issues with Gigamon Technical Support. |
|
disable |
Leave Enable mode and return to Standard mode. |
|
|
Configure email and event notification via email. |
|
enable |
Enter Enable mode. |
|
exit |
Leave Configure mode and return to Enable mode or log out of the CLI. |
|
file |
Manage TCP and debug dump files on disk. |
|
filter-template |
Configures flexible filter templates on GigaVUE‑HC3, GigaVUE-TA100 |
|
gigasmart |
Configures a stack port interface to provide Internet connectivity for a GigaSMART card or module. |
|
gigastream |
Configure a GigaStream – a group of ports acting as a single addressable tool port destination or stack-link. |
|
halt |
Shut down the system without powering it off. |
|
help |
View a description of the interactive help system. |
|
hostname |
Specify the system's hostname. The hostname appears in the system prompt and in SNMP traps. |
|
ib-pathway |
Reserved for future use. |
|
image |
Manage system software images. |
|
interface |
Configure network interfaces. |
|
ip |
Configure IP settings for the eth0 Mgmt port. |
|
ipv6 |
Configure IPv6 settings for the eth0 Mgmt port. |
|
job |
Configure scheduled jobs. |
|
ldap |
Configure LDAP server settings for authentication. |
|
license |
Activate features using license keys. On GigaVUE-TA10A , Use this command to enable clustering on the following TA Series nodes: GigaVUE-TA10, GigaVUE-TA40, GigaVUE-TA100 and GigaVUE‑TA25. |
|
logging |
Configure event logging. |
|
map |
Configure maps and map rules to manage GigaVUE traffic distribution. |
|
map-passall |
Create a pass-all map to send all traffic on a network port to a tool port irrespective of the other packet distribution in place on the port. |
|
map-scollector |
Configure shared collector map parameters. |
|
map-template |
Create a map template. |
|
no |
Delete or clear certain configuration options. |
|
notifications |
Configures notification settings. |
|
ntp |
Enable and disable the use of NTP, as well as add NTP servers. |
|
ntpdate |
Set system clock once from a remote server using NTP. |
|
ping |
Send ICMP echo requests to a specified host. |
|
ping6 |
Send ICMPv6 echo requests to a specified host. |
|
policy |
Configures an active visibility policy. |
|
port |
Configure port type, parameters, and filters. |
|
port-group |
Create a group of ports. |
|
port-pair |
Configure a port-pair on a pair of network ports within the same node. A port-pair is a bidirectional connection in which traffic arriving on one port in the pair is transmitted out the other (and vice-versa) as a passthrough TAP. |
|
radius-server |
Configure RADIUS server settings for authentication. |
|
reload(reboot) |
Reboot or shut down the node. |
|
reset |
Reset specified portions of the system configuration to their factory states. |
|
serial |
Set options for the serial console port. |
|
sfp |
Reserved for future use. |
|
show |
Display configuration and status information for a wide variety of settings and entities. |
|
sleep |
Sleep for a specified number of seconds. |
|
snmp-server |
Configure SNMP settings, including the local SNMP server, notification events, and notification destinations. |
|
spine-link |
Configures spine links in a cluster with a leaf and spine architecture. |
|
ssh |
Enable and disable SSH access, as well as manage settings. |
|
stack-link |
Configure a stack-link between two nodes in a cluster. Stack-links are used to carry data traffic between nodes in a cluster. |
|
system |
Change system settings. |
|
system-health |
Configures system health behaviors. |
|
tacacs-server |
Configure TACACS+ server settings for authentication. |
|
tcpdump |
Display packets from any ethx port in the node on a network. |
|
terminal |
Set terminal parameters, including width and length. |
|
tool-mirror |
Configures a tool-mirror connection between two tool ports. A tool-mirror connection sends all packets arriving on one tool port to a second tool port on the same node. |
|
traceroute |
Trace the route packets take to a destination. |
|
tunnel |
Reserved for future use. |
|
uboot |
Installs new uboot software. |
|
username |
Manage user accounts. |
|
web |
Configure the Web server used for GigaVUE‑FM GUI support on the node. |
|
write |
Save the running configuration to persistent storage. |
